CAD TOOLS AND TECHNIQUE FOR UNIVERSAL JOINT
DOI:
https://doi.org/10.17605/OSF.IO/5GXR9Keywords:
CAD, CAE, Universal JointAbstract
Vehicle transmission framework comprises a few parts which in some cases experience the ill effects of various
burdens (disappointments). An all-inclusive joint comprise of two yokes, one on each pole, associated by crossmolded middle of the road part i.e. creepy crawly. Yoke get together are constantly subjected to torsion and
shear. Era of stress, removal and strain in a general coupling has been broke down. Yoke get together are
turning part and here and there experience the ill effects of weakness by use of variable torque. In this paper
limited component investigation of the part is done to discover the stress and deformation of the last item. For
demonstrating of the segment CAD software is utilized. Pre- handling work like cross section and examination
work is done in ANSYS CAE software. Utilizing FEA investigation, we can recognize the nature and qualities
of stresses following up on the Yoke and evaluate the impact of the load/mass geometry/boundary limit
conditions over the yoke.
Downloads
References
Rahul Arora,” Modeling and Failure Analysis of Universal Joint using ANSYS”, on IJETER, Volume
, Issue 8 Aug. 2017, pp 53-56.
Vishal Rathi and Nitin K. Mandavgade (2009) “Fem analysis of universal joint of Tata 407” Second
International Conference on Emerging Trends in Engineering and Technology, ICETET-09, ISBN:
- 0-7695-3884-6, PP. 98-103.
Nick Cristello, and Yong Kim (2006) “Design optimization of an automotive universal joint
Considering manufacturing cost”, 17th IASTED International Conference Modeling and Simulation,
ISSN: 530-091 , PP. 499–504.
S.K.Chandole, M.D.Shende, M.K. Bhavsar“ Structural Analysis Of Steering Yoke Of An Automobile
For Withstanding Torsion/ Shear Loads”,IJRET: International Journal of Research in Engineering and
TechnologyVolume: 03 Issue: 03 | Mar-2014.
H. Bayrakceken, S. Tasgetiren, I. Yavuz (2007) “Two cases of failure in the power transmission system
on vehicles: A universal joint yoke and a drive shaft”, Engineering Failure Analysis, Vol. 14, ISSN:
- 6307, PP. 716- 724.
Majid Yaghoubi, Ali Jafary, Seyed Saeid Mohtasebi (2010) “Design, simulation and evaluation of a
new universal joint with intersecting angle up to 100 degrees for farm machineries”, AJAE 1(4),
ISSN:1836- 9448, PP: 149-152.
Muhammad Ziaur Rahman, Debasish Adhikary & Tazmin Rashid Mumu (2013) “Failure Analysis of a
Universal Coupling using Finite Element Method
P.G. Tathe, Prof. D.S. Bajaj and Swapnil S. Kulkarni, “Failure Analysis And Optimization In Yoke
Assembly Subjected By Torsion And Shear”, International Journal of Advanced Engineering Research
and Studies E-ISSN2249–8974. JulySept,2014.
Naik Shashank Giridhar, Sneh Hetawal and Baskar P.,“Finite Element Analysis of Universal Joint and
Propeller Shaft Assembly”, International Journal of Engineering Trends and Technology (IJETT) - Nov
– Volume Number 5.
Ashish Bharatrao.Nitalikar, R.D.Kulkarni, Swapnil.S.Kulkarni, “Structural Analysis for a Cardon Joint
in steering column assembly through FEA Techniques”. Asst.Prof.TPCT college of
Engineering,Osmanabad,Director-Able Technologies India Pvt.Ltd,Pune.IJAERS.E-ISSN2249-8974
“Model for localized failure with thermo-plastic coupling: Theoretical formulation and ED-FEM
implementation” Van-Minh Ngo, Adnan Ibrahimbegovic, Delphine Brancherie, Ecole Normale
Supérieure, LMT-Cachan, 61 Avenue du, Président Wilson, 94235 Cachan, France b Université de
Technologie de Compiègne, Laboratoire Roberval, 60205 Compiègne, France article info Article
history: Received 18 October 2012 Accepted 7 December 2012 Available online 20 March 2013.
Tae Hee, Lee Byung Ryul, Ham Seong Oh ,“Study on Steering Column Collapse Analysis using
detailed FE Model”, Hong Advanced Safety CAE Team / Hyundai Motor Co. Korea Paper No. 11-
“TECHNOLOGY FOR SUSTAINABLE RURAL DEVELOPMENT”
NCTSRD 2021
-----------------------------------------------------------------------------------------------------------------------------------------------------
www.iejrd.com SJIF: 7.169 8
In Association with
International Engineering Journal For Research & Development - IEJRD
Dr. Satypal T. Warghat, Dhiraj V. Astonkar, Manish P. Bijwe,”Analysis of differential crown gear and
pinion for axle with different materials, on IJSDR, Volume 4 (4), ISSN: 2455-2631, April 2019, pp
-12
Downloads
Published
How to Cite
Issue
Section
License
This work is licensed under a Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License.
